Canadian TV, Computing and Home Theatre Forums - Reply to Topic

Thread: Fibe TV 4K discussion Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the Canadian TV, Computing and Home Theatre Forums forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:


  Additional Options
Miscellaneous Options

  Topic Review (Newest First)
2019-12-08 10:04 PM
scrooloose Run an Ethernet cable from the HH3000 to the PVR or try the Wi-Fi PODS Bell provides to boost the wireless signal -

2019-12-08 12:48 PM
bobbydance Had Bell fiber optic cable connection installed yesterday in our condo and was upgraded to HH3000. Connection was not in a good place (laundry room) as old coax cable. When using 4K receiver Link light flashes from green light to red (mostly red). Picture quality does not seem to suffer and technician indicated as long as light cycling and no apparent picture problem that this supposedly acceptable. Indicated HH3000 position in condo was the problem and to keep laundry door open to maximize signal.

Any comments ????? suggestions !!!!!
2019-10-20 11:31 AM
Dr.Dave @vanhalen26 If you're watching a 4K channel you have a high bit-rate with fewer motion artifacts than if you're watching a regular HD channel at 720p. You may notice a better picture even if your 4K PVR is set to output 720p. You can change the settings on the PVR to output 1080p, which should give you a better picture when watching a 4K channel. You should also check the picture quality of the HD channels to see which setting gives you a better picture. People have reported varying results, so it may depend on the model of TV and personal preference.
2019-10-20 10:43 AM
57 You can check by pressing the "info or display or recall" or similar button on the TV's remote. If that doesn't work you can check by changing inputs on the TV because it'll usually display the incoming signal for a few seconds when you do this. You can probably set the output of the Fibe box to 1080P on the Fibe 4K boxes if you want, although you may wish to leave it at 720P since that's what the incoming HD signal is. See the following FAQ:

As discussed in the FAQs, most TVs are better at the upconversion than the box, but feel free to experiment to see what works for you.
2019-10-20 07:22 AM
vanhalen26 But is the receiver sending a 1080p picture for TSN4K? For the regular TSN channels it outputs 720p.
2019-10-20 12:25 AM
57 A 1080P TV has no choice other than to display every incoming signal at 1080P. See:

A picture can look better for many different reasons like production values, or better original signal, etc.
2019-10-19 10:45 PM
vanhalen26 If I’m watching fibe on a 4K receiver and playing on a 1080p TV, is the 4K channel displayed in 1080p? The picture does look better to me than the regular channel. Wonder if I’m imagining that.
2019-09-16 05:39 PM
Dr.Dave @dpkost Welcome to the forum. I moved your post to this thread, since we've had some discussion of trying to use 2 Bluetooth remotes. According to this post about 2 years ago, it probably won't work.
2019-09-16 03:28 PM
dpkost I changed to Bell Fibe a few weeks ago. I have a 4k PVR and it comes with a bluetooth slim remote. I got a second remote but I cannot get it programmed to my TV. The first remote works perfectly. The power, volume and mute buttons are programmed to the TV functions correctly.

I tried configuring in the setting on the Bell Fibe box but it would not work. I tried manually configuring by entering the code for my toshiba TV from the user guide paper that came with the remote and that doesn't work either.

Is it possible that you cannot connect 2 bluetooth remotes, that it only supports 1.

Any suggestions would be appreciated.
2019-08-04 06:41 PM
taylormade Thanks to Dr Dave for providing the links to find out what is on in 4K, I had 4k on Cogeco and could not tell from the guide what was actually in 4k. This is a major fail, they try to get everyone to subscribe and then don't show what's on, I even had difficulty finding out online so I cancelled. Looks like now, from Dr Dave's links they are at least documenting online.
2018-12-27 02:58 PM
Dr.Dave @brentmac I believe Bell still limits you to one 4K TV signal per household. You can watch other non-Bell 4K content like Netflix by streaming it directly on your second TV.

It is possible to watch live 4K TV with a second 4K box using the MediaRoom technology that Bell offers. Telus uses similar technology in western Canada and offers a second non-PVR 4k box to their customers.

I see you are posting from Bell Aliant territory. We have a separate Aliant forum, but the 4K technology and a lot of other things are similar since Bell took complete control of Aliant. You may want to use that forum in the future since there are still some differences in pricing, etc.
2018-12-27 01:57 PM
ExDilbert HDMI 4K splitters are available. Beware of vendors advertising basic switches as splitters. They won't power 2 TVs at once. You probably want to search for something like "HDMI Splitter 4K 60HZ 4:4:4 1X2 Port powered." The ones I found cost about $50.
2018-12-27 12:58 PM
brentmac I now have a second 4k television. Is it possible to watch 4k programming on both tv's simultaneously? As well do I need to switch my standard wireless receiver for another 4k receiver? (I already have one 4k)
2018-12-26 11:04 PM
Dr.Dave I copied the instructions for using the Harmony remote with the 4K PVR from the Bell site a couple of years ago. I haven't done that personally, but others confirm it works.

To program any Harmony model, use BELL FibeTV for the manufacturer and VIP5662W for the model.

I set up a Harmony 650? for a family and it lasted about 5 years of very heavy use before the buttons started acting up. They couldn't live without it because it controlled all their devices with a whole bunch of input sources, so they bought a new one. Because I like to tinker, I took the old one apart, cleaned the contacts and it works perfectly.
2018-12-26 10:15 PM
ExDilbert The Harmony 650 is an good remote for the $70 or so that it usually goes for. At $50 it's a good deal. Logitech's other remotes are overpriced. The 880 had a bad button layout which probably explains its lack of popularity. The Harmony One has a great button layout but the build quality was not good. Until something better arrives, I'm buying the Harmony 650.
This thread has more than 15 replies. Click here to review the whole thread.

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

For the best viewing experience please update your browser to Google Chrome