|Topic Review (Newest First)|
|2015-10-07 04:38 PM|
Change Smart Record - PVR Options
I think you meant CBS program, "The Late Show with Stephen Colbert" comes on 032 Global Toronto or 336 Global BC.
I pay extra for the time shift US networks so I expect that the default HD for me would be the US Nets. We use the "Smart Record" feature for shows.
After setting the "Smart Record" from the guide, the default is first HD airing. You can fix all future airings to record the channel you want (032 or 336 or however your 630 is channel mapped) by selecting
VIEW UPCOMING AIR DATES
CHANNELS – select your channel
You should not have to change it again - a one-time thing.
Originally Posted by tvmaster View Post
|2015-10-03 10:52 PM|
Originally Posted by RuralRouter View Post
I don't want to have to edit each one every time. On Thursdays I record The Late Show from CTV since CBS always runs late with NFL, so I avoid CBS on purpose. Shaw must have some agenda recording simul-subs or LNB's we haven't figured out yet
|2015-10-03 10:29 PM|
Originally Posted by LONSat View Post
How do we tell this stupid new software the channel we select is the channel, and time, we want to record from is not up for negotiation?
EDIT: I think I may have figured it out, but what a kluge, and, I'll believe it records the right channel when I see it
|2015-10-03 10:26 AM|
LONSat, I like your idea of being able to user-set the default condition. To each their own
|2015-09-30 12:48 PM|
You can change that by editing the event. A bit of a pain I will admit but you can force it per program to HD only SD only all channels or specific channel. Would be nice if you had the option during the initial setup but maybe in the next version.
It would be to have defaults to turn on off the recording start and stop pop ups AND
a setting to change the default behaviour of the recording setup as noted above or a way to more easily adjust it at the time. Maybe a Smart Recording advanced option where you can set HD/SD/All/Specific channel.
|2015-09-29 11:46 PM|
Originally Posted by RuralRouter View Post
|2015-09-29 07:06 PM|
Default PVR guide pick is first HD showing
I am getting used the the default of 48.14 being first showing of an HD program rather than the exact channel and time I pick from the guide.
|2015-09-29 07:02 PM|
|RuralRouter||The few times I've seen the screensaver, it has always been PPV.|
|2015-09-29 06:39 PM|
|jccamp95||anyone else notice that the PPV channels get removed and the Stingray music ones appear, then the next day its back to PPV, then back to stingray...lather rinse and repeat?|
|2015-09-27 12:13 PM|
|RuralRouter||Sometimes there is a long delay for the receiver to respond to a remote control command due to the GUIDE being downloaded at the time. Downloads take a lot of the processing power when they download and reconfigure the guide. This is normal.|
|2015-09-20 03:06 PM|
The response time from the remote has gotten worse and worse.
Sometimes it takes seconds for the receiver to respond to remote actions.
Its not a remote problem (batteries) because the receiver will act on it.
Like pressing rewind on the remote it can take 10-20 seconds to rewind.
Same thing with other commands.
Sometimes it works fine but eventually it becomes sluggish.
|2015-09-02 10:03 AM|
Smart Record Default & Static Images
RE: Default PVR recording from Menu
Like some have written here, we much prefer the old firmware that allowed picking a channel to Smart Record from the guide and that is the channel that would be recorded, not the new default of Smart Record first HD showing. I just sent an email to Shaw Direct to suggest they revert in their next firmware update.
RE: Pixel Shifting on Static Images
I see that burn-in has occurred to at least one TV set of a contributor to this discussion. I've made my views know to SD, but they insist that Pixel Shifting works. I've stared just inches from the Sting Ray logo on my 65" LED screen; I don't see the pixels moving. Anyway, a logo usually covers more than a few pixels. The logo would have to move entirely to avoid a static image. I don't understand....
|2015-08-13 10:28 PM|
|Billy34||hit exit on remote|
|2015-08-10 01:23 PM|
|kcowan||When I change channels, it shows the new channel at the bottom of the screen for 15 seconds. Is there any way to reduce the time to say 5 seconds. It is really irritating when switching back and forth between football and tennis because the scores are covered up. I know I can hit exit but that gets tiring.|
|2015-08-09 01:31 PM|
|This thread has more than 15 replies. Click here to review the whole thread.|