Canadian TV, Computing and Home Theatre Forums - Reply to Topic
Thread: Multiswitch Discussions Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the Canadian TV, Computing and Home Theatre Forums forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:


  Additional Options
Miscellaneous Options

  Topic Review (Newest First)
2019-12-20 01:26 PM
Jimsathome You need to pull all 4 outputs from the LNB into a multiswitch first, and then distribute them to up to 8 tuners (4 PVRs).
2019-12-20 01:19 PM
Splitting incoming fees

I have 2 feeds coming in to a 630 PVR from an E75 dish.

Is it possible to split these 2 feeds to supply signals to another PVR on a different floor of our house?

Is there multi-switch that will do what I want?
2019-12-09 01:24 AM
Originally Posted by HowardDoin View Post
Iím thinking of changing my ota antenna to something like this ( ). Question is, will it work properly if itís incorporated into my 5x8 multi switch setup? Last thing I want is for it to somehow mess with my satellite signal just to be able to tweak a few ota channels.
Shouldn't be an issue as the frequencies are well separated by at least 50 MHz before being multiplexed (muxed) by the multiswitch. Of course you'll need a diplexer to separate the signals before the input to the Sat Box so you TV's tuner can be used.

If you didn't have a 5x8 Multiswitch in the circuit, a diplexer is used to combine satellite signals (950-2050 MHz) from the dish with Cable or Off-air VHF/UHF signals (5-900 MhHz) into one line. A second diplexer can then be used backwards to split the signals back into two separate lines (one to feed a satellite receiver and another to feed a standard television tuner or cable box).

The diplexer allows DC current through the satellite port to feed and control the LNBF.

A diplexer can also be used to separate the signal coming from a multiswitch with a Cable/Off-air Antenna port.

I hope this is helpful.
2019-12-08 10:15 AM
tvmaster My multiswitch fell out of its enclosure during a storm and into the elements, unbeknownst to me for several days. One output seemed to have died, so I switched to a spare, put her back in the enclosure and all was fine.
Now, a day later, all the outputs seem to be dead, as all my receivers are showing ‘no signal’.
Question - would it fix itself if it were allowed to dry out? Is there a risk to the receivers if not swapped promptly? I have a spare, but it’s not as good as the Eagle Aspen.
Or, would wet weather kill it for good for some reason?

UPDATE: I went to check the AC power supply plug, which is indoors. The coax connector from the power supply (which is connected to the outside coax) was incredibly HOT. I unscrewed it, waited a minute, then screwed it back on - and all my receivers lit up again. Is there a logic circuit inside the power supply that may have become confused? It's been screwed back on for an hour, and is cool to the touch. WTF?
2019-08-29 08:53 PM
HowardDoin Iím thinking of changing my ota antenna to something like this ( ). Question is, will it work properly if itís incorporated into my 5x8 multi switch setup? Last thing I want is for it to somehow mess with my satellite signal just to be able to tweak a few ota channels.
2019-06-24 10:40 PM
Shaw 4x8 muliswitch

I have a truck spec 4x8 muliswitch powered. When I connect all 4 inputs my green light goes off. When I remove one input my green light comes on. Does anyone know why.
2019-04-20 01:02 AM
Jimsathome Glad to hear you got good service from Shaw Direct. Most folks only post to complain. Good stories are a refreshing change. Thanks.
2019-04-19 02:15 PM
starchoice Kudos to Shaw Direct. Was losing the majority of SD feeds on an intermittent but regular basis. Called SD. There was virtually no wait time on the phone. Got a tech who was quick in troubleshooting. Got the system working again but it was temporary. He gave me a reference number for the call which is something I have never received before this. He figured the problem was the multiswitch and I suspected the same because I had the same problem previously many years before this.

Called again. It was a Thursday. She said she would send out a tech. I said if it was the multiswitch. I could swap it out myself but then it seemed like she would need to sell me one. So I said go ahead and send the tech. The first appointment was the coming Sunday (last week). Great. The tech calls me later to ask if he can come Saturday instead, even better. He shows up on time, comes in, no troubleshooting wasting of time, just replaces the switch, was here less than ten minutes and back in business.

My Eagele Aspen S-4180-GX+ (54-2150 MHz) was replaced with a Pico Macom TSMS-4/8 MN (950-2300 MHz).
2019-02-20 12:29 AM
tvmaster Excellent info, thanks for clearing all this up. Both these switches include a connection for OTA antennas, so that makes sense as well.
2019-02-19 10:36 PM
rauschpfeife As long as the switch is good from 950-2150 MHz, you'll be fine. Shaw receivers will only tune within that range, and always less. For dual satellite LNBs (F1, F2), only 950-1450 MHz is used. My fuzzy recollection for the triple satellite LNBs (F1, G1, F2) is that 1052-2127 MHz is used for F1 & G1 and 950-1450 MHz for F2.

Frequencies below 950 MHz are often used for passing terrestrial TV (OTA) through a fifth input terminal. Other switches that work from 250-2150 MHz may have been designed for DirecTV in the States, because some of their LNB technology used that lower range. Anything above 2150 MHz is meaningless.

For all intents and purposes, a switch that supports a wider range than 950-2150 MHz should work just as well for Shaw as one that is restricted to that range.
2019-02-19 12:16 PM
tvmaster ok, thanks. We'll see if anyone with superior technical knowledge to ours chimes in and tells us the significance of the frequency differences...
2019-02-19 02:29 AM
Jimsathome Don't get me wrong tvmaster, the Eagle Aspen was Shaw's chosen multiswitch but they've just moved on since then.

And it may not be for technical reasons as they'd have to change out thousands of working multiswitches. It's more likely it was cost driven, as most large firms will put major purchases like thousands of multiswitches out to bid against a specification. And typically low bid wins.

So while the new "standard" can utilize 950-2300 MHz, Shaw is probably only using a portion of the bandwidth. Say something like nothing below 1000 or above 2100 MHz. Then all of the multiswitches listed above will work just fine. I'm not familiar enough with the details to know what frequencies are being used from the LNB to the Receiver. I guess if I borrowed a scope I could figure it out, but someone here probably knows it already.

I'm just glad you have it sorted.
2019-02-18 08:56 PM
tvmaster So what do you think happens above 2150, satellites in play, transponders etc. At one point, I believe the Eagle Aspen WAS Shawís chosen multiswitch, wasnít it?
2019-02-18 04:00 PM
Glad you got it fixed!


That's an interesting outcome. A while back I too had some issues and ended up replacing my Phillips Multiswitch which was the same vintage / model as yours.

Check this thread:

I changed it to a Steren 201-747 4x8 Sky Switcher Multi-Switch after I couldn't find a Pico Macom TSMS-4/8 (Current Shaw standard).

It's Specifications:

Frequency Range: 950-2300 MHz
Noise Figure: 4.8 dB min
Cross Polar Isolation: 40 dB min
LNB to LNB Isolation: 35 dB min
Rec. to Rec. Isolation: 40 dB min
Control Voltage:
LNB A 13 V/0 kHz
LNB A 17 V/0 kHz
LNB B 13 V/22 kHz
LNB B 17 V/22 kHz
Power Supply Input: 24 Vdc
Receiver Power Input: 13/17 Vdc
Phase III Compatible

The Shaw standard is:

It's specs are pretty much the same. But neither of them fits your Eagle Aspen frequency range. ( 950-2300 MHz Vs. 54-2150 MHz for the Eagle Aspen).

In my situation, once I got the system back working I stopped monkeying around with it (of course!) and never went back to check the Phillips Multiswitch even though I had not fully determined if it was at fault (or the line losses were somehow just too much for it to overcome without the in-line amplifiers.) I also never spent the time to deduce which transponders were involved, or if (like you) the 13v & 18v connections were the problem. Maybe if I get ambitious I'll go back over the data and sort it out.

I didn't scrap the Phillips Multiswitches but suspect they may have contributed to the loss of signal.

What's scary about your problem was the issue was cyclitic and happened at virtually the same time every day. I'm just glad you seem to have it sorted.
2019-02-13 05:39 PM
Looks like the 12-noon signal loss may be solved

I believe the Phillips is the problem. After Jan 21, anything plugged into 13v & 18v was problematic. When I swapped in my backup Aspen Eagle, this problem seemed to go away. If you look at the photos, there is a different frequency range between units. I wonder if Shaw did something, frequency wise, which caused a problem for the Phillips, or if the 13v & 18v dish connections just failed. The Phillips has been up, mostly untouched and working for maybe eight years?

This thread has more than 15 replies. Click here to review the whole thread.

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

For the best viewing experience please update your browser to Google Chrome