|Topic Review (Newest First)|
|2013-03-26 10:57 AM|
|Vader||I would just put a switch in behind the router and make sure all of your computers are connected to the switch.... would not mess with a separate router unless that is all you have :-)|
|2013-03-22 11:45 PM|
Yes, the 2wire can be used as a modem-only. Connect all your computers, devices, etc to your other router like normal. Connect the uplink to the 2wire and you are done.
Note: any Ultimate TV boxes should still be connected directly to the 2wire. While there are reports of them working when connected off other routers this is a highly unrecommended and definitely unsupported configuration.
|2013-03-22 05:08 PM|
To resurrect an old post, can a LAN be utilized just using the 2-wire MTS modem?
MTS seemed to think so but said i should consult an IT guy?
Is there a useful 101 for doing this with the 2-Wire?
I just want communication between 2 or 3 Home PC's for file sharing without any extra equipment if possible?
|2013-02-09 03:12 PM|
|Senk||Please ignore my previous post. I figured out a different way to accomplish what I was trying to do.|
|2013-02-08 09:59 PM|
|Mozza||I have a wireless router attached to my 2wire... but ultimately it's still polling the same IP address - the one that is assigned to the 2wire.|
|2013-02-08 07:36 PM|
I just had my MTS TV and internet installed. They gave me a 2wire 3801hgv gateway.
I'd like to know if it's possible to do this:
Hook a wireless router up to the 2wire and be able to use two different wireless access points - one from the 2wire and one from the router. The reason I want to do this is to get the wireless router permanently hooked to the internet through a VPN service like Witopia or privateinternetaccess. That way I can connect use the router to access the U.S. version of Netflix among other things and still have the 2wire wireless connection available if I need to do something that requires a Canadian IP address.
My primayry concern is trying to determine if this is even possible. Does anyone know? If if it is possible, I'd appreciate if anyone has any tips or know where I could find some instructions.
My router is an Asus WL520GU that is currently running Tomato v1.28 firmware. I'd be willing to get install different firmware or get a new router if necessary.
|2012-03-02 10:40 AM|
|jmorgan||Thanks Vader - I also had lots of issues. First off was the line itself, which MTS fixed. Then if I plugged my STBs into my LAN, recordings played fine, but live TV wouldn't work. If I plugged the STBs into the RG via coax, live TV worked but the recordings were choppy. MTS ended up running CAT5 from the STBs directly to the RG and all seems to be fine now (fingers crossed).|
|2012-03-02 07:30 AM|
Originally Posted by jmorgan View Post
|2012-01-15 08:38 PM|
|crunchermcnut||My PVR list does the same thing from time to time.|
|2012-01-14 12:32 AM|
If you had the means to do it, the 1200s can run on cat5 off the 2wire. Very limited though, as there is only 4 ethernet and 1 is for 1216 and at one for internet (included in installation).
Could be a bad cable end, hidden splitter or splice, junk cable, bad STB, bad 2wire hpna system. This is why we have to run the test. Even if everything looks mint, it could still have problems.
I have a weird issue that I want to figure out. I have RG59 at my 2nd TV, which is over an enclosed ceiling. Sometimes while browsing the PVR list, it'll disappear then slowly repopulate. Strange...
|2012-01-13 03:11 PM|
Originally Posted by Macman View Post
I've also tried plugging the VIP1200s into the switch. They will work fine for 5-10 seconds, and then always say that the TV signal has been lost. I'm not sure why this is. When I plug them back into the 2Wire via coax (as the installer had it), they work fine. Well, except for some serious pixelation issues when playing recordings on one of the VIP1200s, which I may have to call MTS to look at. Unfortunately I never confirmed that the installer did the HPNA tests on the coax!
|2012-01-11 10:59 PM|
|Macman||jmorgan, I don't know the specifics but their installation standards are that the STBs are only to run directly off the 2Wire. I heard that the video stream has priority on the 2wire, or something like that. So I'm guessing that by introducing a switch or two in between would probably screw that up. It might work fine, just sayin'|
|2012-01-11 08:09 PM|
|no123one||Ah yes, no DD-WRT for my WRT160N (rev 2), they only made it for rev 1 and 3. Strange.|
|2012-01-05 03:56 PM|
Originally Posted by Vader View Post
|2011-10-27 04:57 PM|
I had searched for a long time for the DD-WRT for my router and it was always "in progress" but maybe they have one now (or perhaps it wasnt for my hardware revison (2)).
As of today, things are going ok, things seem to be working pretty much leaving things at stock settings on my WRT160N. The only things I changed was to turn off wireless on the 2Wire, set the firewall on the 2Wire to DMZ Plus Mode (which I think is basically OFF), and that's it. My WRT160N router settings are all stock (except I set my own ID name and WPA2 password)
|This thread has more than 15 replies. Click here to review the whole thread.|