How to properly align your satellite dish - Discussion and Tips - Page 57 - Canadian TV, Computing and Home Theatre Forums

dr.opie · 2012-04-21, 02:21 AM

Yes everything was hooked up properly, mast was level and plumb.
obviously had it aimed and set close to right because I tried another newer lnbf again off a friends dish put it on mine and got 53% signal in the same spot same direction now its flipping from 99 - 100% on transponder 13 on 91.
Whats the chances of getting 3 bad lnbfs? even if they are really old lol
Anyway thanks for the help guys

RKM01 · 2012-04-21, 07:28 AM

Hello all I am a total newbie to this stuff but I have a question regarding the aiming of my dish. On the net I found that I should be grabbing the 91 signal for hi def which they say is in the 90 degree range but bell literature says grab the 82 at 208 degrees. Living in huntsville ontario where should I be aiming for a 9200 receiver?

Pinza · 2012-04-21, 08:10 AM

You need the bird at 82 degrees for HD.

RKM01 · 2012-04-22, 08:05 AM

Thank you for the information Pinza!

monkeyhunk · 2012-05-06, 11:36 PM

If you're hitting either 91 on the left hand slot or 82 on the right hand slot of the y you should be hitting the other by default given that your skew is right.

bbakernbay · 2012-05-17, 08:55 PM

I've got the HD TV and the HD receiver authorized but my son forgot to bring the dual LBNF 20" Dish with him and we just have our 18" dish with the single LBNF

All we ever watch is High Def - Can I readjust the 18" dish to find the HD Satellite and run the signal through the HD Receiver?

He won't be back for 6 weeks so I was hoping I could improvise in the meantime.

Is it possible? If so, any tips on what adjustments are needed to find SAT 2

m3repair · 2012-05-17, 09:19 PM

Yes you can point at 82 only with your 18 and get HD channels but of course no SD channels, if thats good for you then go ahead and do it, only issue I an think of is possibly not getting guide updates as they are strictly on 91 I believe. (Someone chime in and confirm updates and guide are on Transponder 13 on 91, or is it both) either way everything would work minus that possibly. If you find 91 your not far off from finding 82 when you aim the dish, good luck!

rogue17 · 2012-05-17, 10:45 PM

Hi bbaker, I think I read somewhere that you can get updates through sat 82.

But I thought you needed the 20" dish in order to get HD as this dish has the swivel that allows to tilt the dish. But I can be wrong.don't know much myself. Pinza or joelouie know this stuff inside out.

Interceptor · 2012-05-18, 02:30 AM

If you don't have 91, you won't get any guide updates and I know that the PVR record functions won't work on a 6131. Your guide will show about 2 hours ahead though. Otherwise you're good to go.

bbakernbay · 2012-05-18, 10:11 AM

Thanks guys, it certainly appears to be doable based upon your responses.

I'll check back in after the revisions.

JoeLouie · 2012-05-18, 08:51 PM

Quote:

Originally Posted by rogue17

Hi bbaker, I think I read somewhere that you can get updates through sat 82.

But I thought you needed the 20" dish in order to get HD as this dish has the swivel that allows to tilt the dish. But I can be wrong.don't know much myself. Pinza or joelouie know this stuff inside out.

I can't give a definite answer on if you'll get the guide with only 82 or not (too lazy to go outside and check with my dish lol), but it will definitely work pointed only at 82. You need a 20" dish if you want it pointed at 91 AND 82, but if you're fine without you SD for now just point it slightly to the left and up a bit and you should be hitting 82.

WakenBlake · 2012-05-20, 06:04 PM

Hello!

I am trying to install a satellite to run a 9241 reciever, but I am running into a few problems. Whether it is is ignorance in techniques used in installations or hardware issuses, I am not sure.

To start:
I am located just north of Huntsville Ontario. I having been trying to install the satllite for a while now and have run into a lot of problems. Today I was finally able to at least make a connection to one of the satellites- at times a 100% connection to 82, but no connection to 91. This leads me to believe that the LNBF is pointing to the wrong satellite altogether.

I know that the usual response is to aim for 91 and 82 will come, but I am having an EXTREMELY hard time picking up any singal at all. So I am nervous to lose what progress I have now.

After this I tried to replace the two seperate LNBFs with a DPP quad LNBF to ensure I was using the newest equipment- no signal.

So I guess my two questions are:
How do I go from making a great connection on 82 to connecting to 91 at all?
Would there be any change in the aiming process from using a DPP quad and two seperate LNBFs?

Installer · 2012-05-20, 09:51 PM

after changing to the dpp you would have to do a "check switch" in order for the receiver to show signal.
is your dish skewed properly? are you receiving 82 on the correct lnb? if not that would explain your problem...let us know and we'll be able to tell you where what direction to move your dish to lock both.

jdevlin · 2012-05-21, 09:59 PM

Did you try different transponders? I am not sure which ones are not working currently, if any, but I have been stung in the past by aiming and using a transponder that was not on.

mitigator · 2012-06-11, 02:32 AM

I'm about to get my house roof re shingled and contacted BellExpress Vu who said they could schedule an Installer to re calibrate the Dish the day after the shingles are done for a $75.00 charge. Now the Roofer has agreed to remount the Dish once the job is done. I have a ladder to climb the roof, but one of my knees requires surgery. Is there an easy way to re-aim & set up the Bell Dish possibly with the Roofer?

2012-05-17, 08:55 PM	#846
bbakernbay Rookie Join Date: Apr 2012 Posts: 8	Can You Get High Def with Single LBNF Dish I've got the HD TV and the HD receiver authorized but my son forgot to bring the dual LBNF 20" Dish with him and we just have our 18" dish with the single LBNF All we ever watch is High Def - Can I readjust the 18" dish to find the HD Satellite and run the signal through the HD Receiver? He won't be back for 6 weeks so I was hoping I could improvise in the meantime. Is it possible? If so, any tips on what adjustments are needed to find SAT 2

2012-05-20, 06:04 PM	#852
WakenBlake Rookie Join Date: May 2012 Posts: 1	Found 82, no 91 Hello! I am trying to install a satellite to run a 9241 reciever, but I am running into a few problems. Whether it is is ignorance in techniques used in installations or hardware issuses, I am not sure. To start: I am located just north of Huntsville Ontario. I having been trying to install the satllite for a while now and have run into a lot of problems. Today I was finally able to at least make a connection to one of the satellites- at times a 100% connection to 82, but no connection to 91. This leads me to believe that the LNBF is pointing to the wrong satellite altogether. I know that the usual response is to aim for 91 and 82 will come, but I am having an EXTREMELY hard time picking up any singal at all. So I am nervous to lose what progress I have now. After this I tried to replace the two seperate LNBFs with a DPP quad LNBF to ensure I was using the newest equipment- no signal. So I guess my two questions are: How do I go from making a great connection on 82 to connecting to 91 at all? Would there be any change in the aiming process from using a DPP quad and two seperate LNBFs?

2012-05-20, 09:51 PM	#853
Installer Join Date: Mar 2011 Posts: 292	after changing to the dpp you would have to do a "check switch" in order for the receiver to show signal. is your dish skewed properly? are you receiving 82 on the correct lnb? if not that would explain your problem...let us know and we'll be able to tell you where what direction to move your dish to lock both. __________________ "The quality of your question will directly effect the quality of your answer"

2012-06-11, 02:32 AM	#855
mitigator Join Date: Feb 2011 Posts: 80	Re-aiming Bell Dish After Shingling Job I'm about to get my house roof re shingled and contacted BellExpress Vu who said they could schedule an Installer to re calibrate the Dish the day after the shingles are done for a $75.00 charge. Now the Roofer has agreed to remount the Dish once the job is done. I have a ladder to climb the roof, but one of my knees requires surgery. Is there an easy way to re-aim & set up the Bell Dish possibly with the Roofer?

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

2012-04-21, 02:21 AM	#841
dr.opie Rookie Join Date: Apr 2012 Posts: 5	Yes everything was hooked up properly, mast was level and plumb. obviously had it aimed and set close to right because I tried another newer lnbf again off a friends dish put it on mine and got 53% signal in the same spot same direction now its flipping from 99 - 100% on transponder 13 on 91. Whats the chances of getting 3 bad lnbfs? even if they are really old lol Anyway thanks for the help guys

2012-04-21, 07:28 AM	#842
RKM01 Rookie Join Date: Apr 2012 Posts: 2	Hello all I am a total newbie to this stuff but I have a question regarding the aiming of my dish. On the net I found that I should be grabbing the 91 signal for hi def which they say is in the 90 degree range but bell literature says grab the 82 at 208 degrees. Living in huntsville ontario where should I be aiming for a 9200 receiver?

2012-04-21, 08:10 AM	#843
Pinza Veteran Join Date: Jul 2008 Location: GTA Posts: 8,572	You need the bird at 82 degrees for HD.

2012-04-22, 08:05 AM	#844
RKM01 Rookie Join Date: Apr 2012 Posts: 2	Thank you for the information Pinza!

2012-05-06, 11:36 PM	#845
monkeyhunk Join Date: May 2012 Location: ON Posts: 386	If you're hitting either 91 on the left hand slot or 82 on the right hand slot of the y you should be hitting the other by default given that your skew is right.

2012-05-17, 09:19 PM	#847
m3repair Join Date: May 2011 Location: Etobicoke, ON Posts: 378	Yes you can point at 82 only with your 18 and get HD channels but of course no SD channels, if thats good for you then go ahead and do it, only issue I an think of is possibly not getting guide updates as they are strictly on 91 I believe. (Someone chime in and confirm updates and guide are on Transponder 13 on 91, or is it both) either way everything would work minus that possibly. If you find 91 your not far off from finding 82 when you aim the dish, good luck!

2012-05-17, 10:45 PM	#848
rogue17 Join Date: Nov 2011 Posts: 553	Hi bbaker, I think I read somewhere that you can get updates through sat 82. But I thought you needed the 20" dish in order to get HD as this dish has the swivel that allows to tilt the dish. But I can be wrong.don't know much myself. Pinza or joelouie know this stuff inside out.

2012-05-18, 02:30 AM	#849
Interceptor Join Date: Sep 2005 Location: Sunshine Coast Posts: 593	If you don't have 91, you won't get any guide updates and I know that the PVR record functions won't work on a 6131. Your guide will show about 2 hours ahead though. Otherwise you're good to go.

2012-05-18, 10:11 AM	#850
bbakernbay Rookie Join Date: Apr 2012 Posts: 8	Thanks guys, it certainly appears to be doable based upon your responses. I'll check back in after the revisions.

2012-05-21, 09:59 PM	#854
jdevlin Join Date: Nov 2009 Location: Wainfleet Posts: 464	Did you try different transponders? I am not sure which ones are not working currently, if any, but I have been stung in the past by aiming and using a transponder that was not on.