Just wondering exactly what the wiring scheme will be after I have FibreOp installed in a few weeks. I currently have Aliant High Speed Ultra DSL Internet and Bell Satellite TV. Right now, my Internet is set up so that a dedicated run of Cat 5e travels from the phone junction box near my electrical panel in the attached garage, to the router which is located on the second floor of the house in my office. All phone lines in the home are wired using Cat 5e, and presently all TV's are set up in a home run configuration to the electrical panel using RG6 (satellite) cable.
Bell Aliant will be installing the PVR plus 2 additional set top boxes. I assume that the ONT will be installed near my electrical panel in my garage. My questions concern the wiring from the ONT to the router / to the STB's. Does each STB require a dedicated run of Cat 5e from the router to the STB? Or do the slave (non-PVR) units require a run of Cat 5e from the PVR to each non-PVR box?
I'm sure these questions sound dumb to those who already have the service installed. I just want to know what I'm in for, and if necessary, I might run the cable myself to ensure a tidy installation. I'm also strongly leaning toward picking up an Asus RT-N56U, as from what I have read it greatly improves the TV user experience.
Any clarification on the setup would be greatly appreciated.
My ONT is outside, on the side of the house. A cable from that comes inside and connects to the ActionTec.
In my case that was very unconveniently located in the basement, so the installer ran Cat5e from there across the house and up a floor, which plugs into a Netgear router, and the wired computers/xbox/ps3 connect to that. The house was already wired for cable when we moved in, and for TV they simply reused that wiring (which was convenient).
You can't "split" Cat5 directly, but you can plug the one that goes up there into a hub/switch/router (with the DHCP server turned off so it acts like a switch) and then plug your two computers into that.
That's how mine is set up actually. I have one Cat5e cable going from the Aliant router up a floor, and that goes into my Netgear 3700. Then my two desktop PCs and the Xbox 360 all plug into the Netgear. There's only one cable going to the Actiontec that way and things are happy.
If you don't want to use a second switch, then yes you'd have to run a second cable to the Actiontec for an additional computer.
I tried to run my own Cat5e today but it was such a PITA, I had to quit. Coping with all that blown-in insulation in the attic was a nightmare!
So now I am faced with a bit of a dilemma. It is no problem to get a couple runs of Cat5e to two of my TV's, however, the one in the MBR is a different story. Since RG6 is already in place for all three TV's, will the installer simply use this for the TV signal? Can you mix and match (2 tv's on Cat5e, 1 on RG6)? Is the Asus RT-N56U compatible with setups where RG6 is used to feed the tv's?
If you are doing ethernet then you need separate runs from something (a switch). If you are using coaxial from the Actiontec then that goes to a splitter, which then goes to each STB. Same goes for the Trendnet coax converter.
The STB may act in a switch configuration as Danster indicates allowing it to perform the ethernet <-> coax conversion but I personally do not support or recommend it.
That's how they installed my setup. I guess I'm happy I'm not paying for the box should it go Pouf! in the middle of the night.
I will see what they recommend for an install, but my house is less than 2 years old, so I don't foresee running ethernet cable around baseboards, etc. Like you said, if it's installed by their technician then it should be covered if any issues crop up.
In the middle of my install right now, so prompt feedback would be HUGELY appreciated. I am able to get Cat5e from the actiontec to 2 of my STB's, including the PVR. The other one will be running on Coax from the actiontec. The installer has supplied me with a Corinex AV256 CableLAN box. Any idea how this should figure into the install of the RT-N56U? Which cables should be connected to which ports? Thanks.